Heidenhain TNC 620 (34056x-04) Cycle programming Manual de usuario Pagina 282
- Pagina / 468
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using Touch Probe Cycles
13.3 Touch probe table
13
282
TNC 620 | User's Manual Cycle Programming | 5/2013
Touch probe data
Abbr. Inputs Dialog
NO
Number of the touch probe: Enter this number in the
tool table (column: TP_NO) under the appropriate tool
number
–
TYPE
Selection of the touch probe used
Selection of touch probe?
CAL_OF1
Offset of the touch probe axis to the spindle axis for the
reference axis
TS center misalignmt. ref. axis?
[mm]
CAL_OF2
Offset of the touch probe axis to the spindle axis for the
minor axis
TS center misalignmt. aux. axis?
[mm]
CAL_ANG
The TNC orients the touch probe to the orientation angle
before calibration or probing (if orientation is possible)
Spindle angle for calibration?
F
Feed rate at which the TNC is to probe the workpiece
Probing feed rate? [mm/min]
FMAX
Feed rate at which the touch probe pre-positions, or is
positioned between the measuring points
Rapid traverse in probing cycle?
[mm/min]
DIST
If the stylus is not deflected within the defined path, the
TNC outputs an error message
Maximum measuring path? [mm]
SET_UP In SET_UP you define how far from the defined (or
calculated) touch point the TNC is to pre-position the
touch probe. The smaller the value you enter, the more
exactly you must define the touch point position. In
many touch probe cycles you can also define a set-
up clearance that is added to the SET_UP machine
parameter.
Set-up clearance? [mm]
F_PREPOS
Defining speed with pre-positioning:
Pre-positioning with speed from FMAX: FMAX_PROBE
Pre-positioning with machine rapid traverse:
FMAX_MACHINE
Pre-positioning at rap. traverse?
ENT/NO ENT
TRACK To increase measuring accuracy, you can use TRACK
= ON to have an infrared touch probe oriented in the
programmed probe direction before every probe
process. In this way the stylus is always deflected in the
same direction:
ON: Perform spindle tracking
OFF: Do not perform spindle tracking
Orient touch probe cycles?
Yes=ENT, No=NOENT
- User’s Manual 1
- Cycle Programming 1
- About this Manual 4
- Intended place of operation 9
- Legal information 9
- Fundamentals 10
- 73498x-02 10
- Contents 11
- Fundamentals / 39
- Overviews 39
- Fundamentals / Overviews 40
- 1.1 Introduction 40
- Available Cycle Groups 1.2 41
- 1.2 Available Cycle Groups 41
- Using Fixed Cycles 43
- 2.1 Working with fixed cycles 44
- Working with fixed cycles 2.1 45
- Using GLOBAL DEF information 49
- Entering PATTERN DEF 53
- Using PATTERN DEF 53
- Defining a single pattern 55
- Defining a full circle 57
- Point tables 2.4 59
- 2.4 Point tables 59
- Drilling 63
- Fixed Cycles: Drilling 64
- 3.1 Fundamentals 64
- G240, software option 19) 65
- DRILLING (Cycle 200) 3.3 67
- 3.3 DRILLING (Cycle 200) 67
- G204, software option 19) 77
- 3.11 Programming Examples 90
- Programming Examples 3.11 91
- Tapping / Thread 93
- 4.1 Fundamentals 94
- ISO: G207) 100
- Cycle run 101
- Cycle parameters 103
- Prerequisites 105
- G262, software option 19) 107
- 4.11 Programming Examples 126
- Programming Examples 4.11 127
- Fixed Cycles: 129
- Pocket Milling / 129
- Stud Milling / Slot 129
- 5.1 Fundamentals 130
- G253, software option 19) 139
- G254, software option 19) 143
- G257, software option 19) 152
- 5.8 Programming Examples 156
- Programming Examples 5.8 157
- Pattern Definitions 159
- 6.1 Fundamentals 160
- G221, software option 19) 164
- 6.4 Programming Examples 166
- Programming Examples 6.4 167
- Contour Pocket 169
- Fixed Cycles: Contour Pocket 170
- 7.1 SL Cycles 170
- SL Cycles 7.1 171
- Superimposed contours 7.3 173
- 7.3 Superimposed contours 173
- G120, software option 19) 177
- G121, software option 19) 179
- G123, software option 19) 184
- G124, software option 19) 185
- G125, software option 19) 187
- Programming Examples 7.10 189
- 7.10 Programming Examples 189
- Cylindrical Surface 195
- 8.1 Fundamentals 196
- ISO: G127, software option 1) 197
- 8.5 Programming Examples 206
- Programming Examples 8.5 207
- Defining contour descriptions 212
- Superimposed contours 214
- Contour description programs: 219
- Multipass Milling 223
- 10.1 Fundamentals 224
- G231, software option 19) 227
- G232, software option 19) 231
- Programming Examples 10.5 235
- 10.5 Programming Examples 235
- Cycles: Coordinate 237
- Transformations 237
- 11.1 Fundamentals 238
- (Cycle 7, DIN/ISO: G53) 240
- Editing mode of operation 242
- Configuring the datum table 244
- To exit a datum table 244
- Status displays 244
- G80, software option 1) 253
- Resetting 255
- Workspace monitoring 256
- Programming Examples 11.10 259
- 11.10 Programming Examples 259
- Cycles: Special 261
- Functions 261
- Cycles: Special Functions 262
- 12.1 Fundamentals 262
- Function 263
- ISO: G36) 266
- Cycle function 267
- ISO: G225) 270
- Using Touch Probe 273
- Using Touch Probe Cycles 274
- Probe Cycles 277
- Multiple measurements 279
- Touch probe table 13.3 281
- 13.3 Touch probe table 281
- Touch Probe 283
- Cycles: Automatic 283
- Measurement 283
- Misalignment 283
- 14.1 Fundamentals 284
- Fundamentals 14.1 285
- Datum Setting 303
- 15.1 Fundamentals 304
- Fundamentals 15.1 305
- Workpiece 355
- Inspection 355
- 16.1 Fundamentals 356
- Fundamentals 16.1 357
- G420, software option 17) 364
- G421, software option 17) 367
- G431, software option 17) 392
- 16.14 Programming Examples 395
- Programming Examples 16.14 395
- 17.1 Fundamentals 400
- G460, software option 17) 405
- 5 TCH PROBE 461 CALIBRATE TS 407
- Q434=+5 ;DATUM 407
- Kinematics 413
- Overview 415
- 18.2 Prerequisites 416
- ISO: G450, Option) 417
- Logging function 418
- Notes on data management 419
- DIN/ISO: G451, option) 420
- Positioning direction 422
- Notes on the accuracy 425
- Backlash 427
- Various modes (Q406) 432
- DIN/ISO: G452, option) 434
- Drift compensation 441
- Tool Measurement 445
- 19.1 Fundamentals 446
- Fundamentals 19.1 447
- Tables of Cycles 461
- 20.1 Overview 462
- Overview 20.1 463
- Touch probes from HEIDENHAIN 468
Relacionado con productos y manuales para Equipo Heidenhain TNC 620 (34056x-04) Cycle programming
Equipo Heidenhain TNC 620 (73498x-01) Manual de usuario
(559 paginas)
(559 paginas)
Equipo Heidenhain TNC 620 (73498x-01) Manual de usuario
(547 paginas)
(547 paginas)
Equipo Heidenhain TNC 620 (73498x-01) Manual de usuario
(559 paginas)
(559 paginas)
Equipo Heidenhain TNC 620 (73498x-01) Manual de usuario
(555 paginas)
(555 paginas)
Equipo Heidenhain TNC 620 (73498x-01) Manual de usuario
(559 paginas)
(559 paginas)
Equipo Heidenhain TNC 620 (73498x-01) Manual de usuario
(575 paginas)
(575 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales